Lego – Basing Minifigs for Wargaming

This is a bit of a tutorial/instructional post and I’m hoping informative and useful to others who may wish to use Lego minifigs for wargaming (Part2 here). One of the fundamental problems with using Lego minifgs for wargaming is they don’t have a base and if you try to just field them as is they end up falling over and getting knocked over a lot. Now you could try sticking them to radar dishes or flat square bases,  however you’ll then be adding height to your already slightly over-sized troopers or worse for most fantasy games they wont rank up well in movement trays and the bases are still very light. Now you could buy these from Minifig For Life:

However I had 3 issues with these, firstly at 0.65 euro’s (0.80 – 0.90 AUD) each it gets expensive fast. I estimated I needed 40-60 of them to start with so  I was  looking at close to $50AUD just for bases (not counting shipping).  Secondly they appear quiet small my estimate is 3/4 inch – 20mm round slightly under the 25mm standard round base and made of plastic so they might be to light and small to keep minifigs upright. Thirdly I had to order them from OS which of course means more $$$ for postage. I like to spend my money on paper or lego not postage, however if I lived in europe I probably would have jumped on them to save time and energy :).

So I started to look around what could I use to make nice bases. Washes come in a nice 25mm size (25mm/1inch diameter) with a hole in the middle, are cheap (10-15c)  and heavy,  I thought I could simply bond a flat plate of lego over the hole (Yes, glue a piece of lego permanently to something hence destroying it forever, my lego protective gene had issues with this to, however my need was to great).  It was partial success the flat plate caused to much of an increase in height and looked very glued on. Hunting around  Bricklink I found the below part which is the top part of 2×2 turntable part no 3679, even better you can get them for around 1-3 cents each and they are very thin vertically:

Now the process of actually creating the bases is fairly simple. Grab 1 of your 25mm washers (1 inch), next grab 1 x 3679 (the above part), take a small dob of 2 part epoxy glue and place it around the outside of the inner washer hole (Araldite or some other brand, I find the 5min stuff best and use a cheap no-name brand from the $2 shop not like anyone’s ever going to see it):

Next place part number 3679 over the washer hole (center it relative to the outside edge of the washer) and push it into the glue, make sure the glue doesn’t bulge up higher or across the flat part of 3679 or your minifig’s will have problems being placed on the base:

Next I spray painted the whole lot black using a cheap enamel spray for durability (keep the coat thin). If you want for example desert bases change the enamel spray to a light brown or desert orange basically a colour that matches your planned finishing look (I prefer black with green :), personal choice):

I quiet literally have heaps of flock laying around and just grabbed some green flock to use, but you could use sand or any other standard wargaming basing technique just make sure your Lego interface piece (3679) stays free of flock/sand and other bits of decoration:

Now your lego armies soldiers can traverse the most difficult of Felt terrain without any problems:

Hopefully this information was slightly useful to someone 🙂

3 Responses to “Lego – Basing Minifigs for Wargaming”


  1. 1 BIG RICH March 28, 2011 at 2:15 am

    Very cool. Good idea.

  2. 2 Matthias January 3, 2014 at 7:07 pm

    This bases are awesome! Great idea! Thanks for sharing!


  1. 1 Lego – Basing Minifigs for Wargaming (Part 2) | Sirrob01 Trackback on August 18, 2013 at 3:51 am

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s




Project Status


WWII Project First Release

80%


B-tech Buildings Five

20%


Design Victorian era City

15%


Something Different

5%


Enter your email address to follow this blog and receive notifications of new posts by email.

Join 104 other followers

Content Released Under

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 3.0 Unported License.
Please Attribute to Sirrob01 with a link back to my blog

%d bloggers like this: